Cables

⬇︎ Full List of Specs and Features Below ⬇︎ This cable connects your Controller receiver to your VESC. It's usually always an after thought wh...

⬇︎ Full List of Specs and Features Below ⬇︎ Building a dual motor electric skateboard? This servo Y-cable allows you to drive two VESCs or ESC...

⬇︎ Full List of Specs and Features Below ⬇︎ A simple extension cable to help you on your build. Features 1 female connector and 1 male connect...

⬇︎ Full List of Specs and Features Below ⬇︎ Don't buy more than you need! Save money and buy exactly the amount for your project. 14 Gaug...

A simple cable to connect your motor's sensor wire into a Vesc.  Convert 1.5mm JST to 2.0 JST Cable Length: 100mm-110mm 

⬇︎ Full List of Specs and Features Below ⬇︎ Used to connect 2 FSESC ESCs together.  What's In The Box?- (1) Canbus Connection Cable

⬇︎ Full List of Specs and Features Below ⬇︎ Finally a solid App for DIY Electric Skateboards. Log rides, create different ride modes, track ...

Supports Charging (Phone, Remote, etc.)Supports Data Transfer (Programing Vescs)3 Foot Cable Length

Supports Charging (Phone, Remote, etc.)Supports Data Transfer (Programing Vescs)3 Foot Cable Length

⬇︎ Full List of Specs and Features Below ⬇︎ A simple 2 pronged power cord for our battery chargers or what ever you may need one for. Fits most...

Used to connect 2 VESC® based ESCs to 1 Battery. Simply plug in each VESC® based ESC to each of the female XT60 connectors and plug the battery i...

⬇︎ Full List of Specs and Features Below ⬇︎ Male MR30 to Male 4mm Bullet connector adapter. Used to adapt Direct Drive connections to regular ES...

⬇︎ Full List of Specs and Features Below ⬇︎ Female MR30 to Female 4mm Bullet connector adapter. Used to adapt the Hobbywing ESC to other motors....

*PLEASE NOTE* This is a replacement power switch that is compatible with the following ESCs: Single Belt ESCDual Belt ESCDual Hub ESC This Power Bu...

Use this cable to adapt a 6 pin motor hall sensor wire to a 5 pin sensor port.  Input: JST PH 2.0mm 6 Pin Output: JST PH 2.0mm 5 Pin Cable Length:...

Use this cable to extend your 6 pin hall sensor wires. Input: JST PH 2.0mm 6 Pin Output: JST PH 2.0mm 6 Pin Cable Length: 200mm 26awg

Use this cable to extend your 5 pin hall sensor wires. Input: JST PH 2.0mm 5 Pin Output: JST PH 2.0mm 5 Pin Cable Length: 200mm 26awg

Use this cable to adapt a 5 pin motor hall sensor wire to a 6 pin sensor port.  Input: JST PH 2.0mm 5 Pin Output: JST PH 2.0mm 6 Pin Cable Lengt...

2 Pin JST 2.0 connector to raw leads.  26awg Wire. Approximately 120mm in length. Compatible with:Battery Percentage IndicatorFocBox 2 Pin Port Us...

Use this adapter to plug your motors with 4mm bullet connectors into a FOCBOX Unity/Tenka.  Cable Length: 1.5in  |  38mmCable AWG: 12AWG Sold as a...

TPU Cable Brackets to keep the inside of your enclosure nice and neat. The neater your set up, the cooler your board will run.  Included: (3) Large...

XT30 Female Connector16awg Wire, 150mm Length

XT30 Male Connector16awg Wire, 150mm Length

XT60 Female Connector12awg Wire, 280mm Length